
Printing a zine on a screen press is a question of sheets, not pages. Each sheet is printed on both sides, folded, and nested with the others. The pages on a sheet sit in an order that only makes sense once it is folded, and the planning has to be right before the first film is made.
Saddle stitch: page order
Saddle stitch means folded sheets nested inside each other and stapled through the fold. Every sheet adds four pages, so the page count must divide by four. A sheet is printed on both sides, with two pages on each side, which is why page 1 sits next to the last page:
| Sheet (8-page zine) | Front side | Back side |
|---|---|---|
| Outer sheet | 8 | 1 | 2 | 7 |
| Inner sheet | 6 | 3 | 4 | 5 |
A 16-page zine adds two more sheets, and so on. A planner does this for you: the imposition planner lays the pages on press sheets in the right order for saddle stitch, glued or sewn binding, and it is free.
Creep
When sheets are nested, the inner ones sit further round the fold. After folding, the fore-edge of the inner sheets sticks out further than the outer ones, and when you trim it flat the margin of the inner pages is narrower. That is creep.
The cure is to move the content of the inner sheets towards the spine, a little more for each sheet you go in. The shift per sheet is about the paper thickness: 0.1 mm is a common starting value, measured on a stack of your own paper. The more sheets, the more it matters; a four-page zine does not need it, a 64-page one does.
Glued and sewn books
- Glued: signatures of 4, 8 or 16 pages are glued at the spine. The spine is milled off before gluing, so each page loses a little width at the spine and the content has to move away from it. The milling allowance, about 3 mm, is a typical start. Ask your binder.
- Sewn: signatures of 4, 8 or 16 pages are sewn. No creep and no milling allowance to plan for.
A separate cover
A cover on its own stock is made from the first two and the last two pages of your file. For saddle stitch it is two pages wide, inside and outside. For glued and sewn books it is back, spine and front, and the spine width follows from the page count and the paper thickness.
Printing the sheets
- One film per sheet side and ink. A zine of four sheets in one ink is eight films. Every film is mirrored for emulsion-down exposure and carries registration marks and fold marks.
- Register the back to the front. Use the same marks on both sides, and let the first side dry before you print the second.
- Paper moves with humidity, more across the grain, which hurts registration when you print several colours. Print all colours in one session (see paper by job and mesh).
- Check the order with a dummy. Fold a blank sheet, write the page numbers on it and compare with the plan before you expose a single screen.
In PrintFilmReady
The Pro book panel takes your pages as a PDF or as images, lets you pick saddle stitch, glued or sewn and the page and sheet size, applies creep or milling, plans the cover, and makes one film per sheet side and ink. The planner and the page order are free; the films are Pro.
Common questions
How many pages can a saddle-stitched zine have?
Any multiple of four. Each folded sheet adds four pages.
What is creep in a booklet?
The inner sheets of a nested booklet stick out further at the fore-edge after folding. The content has to move towards the spine, a little more for each sheet inwards, so the margins are equal after trimming.
How big is the creep?
About the paper thickness per sheet is a common starting value, around 0.1 mm. Measure a stack of your own paper and print a dummy.
What is the milling allowance?
In a glued book the spine is milled off, so the pages lose a little at the spine. A start of about 3 mm is typical; ask your binder.
Do I need to plan creep for a glued or sewn book?
No creep for sewn books. A glued book needs the milling allowance instead.
Plan your zine
The imposition planner puts the pages on press sheets for saddle stitch, glued or sewn binding. Free, in your browser.
Built by a screen printer, for screen printers. What you tell us decides what gets built next. Write a review · Send an idea