
The short version
Paper is the part of the stack you can change last and regret first. The same film and the same screen print differently on a smooth uncoated sheet, a cotton rag sheet and a gloss coated sheet, so decide the paper from the job and then set the screen to suit it. These are starting points, not standards. Every row below should be confirmed with a test strip on your own paper and ink (there is a one-evening test at the end).
| Job | Paper to start with | Mesh (threads per inch) | Watch out for |
|---|---|---|---|
| Bold flats, gig poster, 1–4 spot colours | Smooth uncoated cover, about 200–300 g/m² | 110–160 for solids, up to about 200 for text and line work | Cockling when wet prints are stacked; rack space |
| Fine-art edition with a soft, matte look | Cotton rag or printmaking paper, 250–300 g/m² and up | 156–230 | Water-based ink sinks in and looks flatter; print all layers in one session |
| Photographic halftone, fine detail | Smooth uncoated, or a matte or silk coated sheet | 230 for halftones, 280–305 for the finest detail | Rough surface breaks up the small dots |
| Layered, transparent overprints | Smooth, bright white uncoated | 156–230 | The paper white is your lightest “ink”: a cream sheet tints every colour |
| Dark or coloured stock | Dense uncoated, 250 g/m² and up | 110–156 for the opaque white layer | White usually needs two passes; semi-transparent inks vanish |
| Gloss or coated stock | Coated sheet made for the purpose | 156–230 | Water-based ink does not bond; slow drying; test adhesion |
| Metallic or fluorescent ink | Smooth uncoated or coated, per the ink maker | Follow the ink’s data sheet | Sources disagree on mesh; do not guess |
What the paper does to your print
Seven properties decide almost everything. Learn to read them on the packaging or the merchant’s data sheet and most of the choice makes itself.
- Weight (g/m²). Weight is stiffness and flatness. Print services recommend about 244–300 g/m² for posters, and poster suppliers sell 200 and 250 g/m² uncoated sheets. Screen printers quote the US “cover” weights: 68 lb is about 184 g/m², 80 lb about 216, 100 lb about 270. As a rule of thumb, light stock under roughly 150 g/m² cockles under wet ink and sticks to the screen more easily. That boundary is an indication, not a standard.
- Surface. Smooth sheets hold fine dots. Textured and rough sheets let the ink find its own way into the valleys, so small dots deform and fine lines break up. Halftone and process work needs the smoothest stock you can afford.
- Absorbency and sizing. Sizing controls how much ink sinks in. A lightly sized, absorbent sheet drinks the ink: matte, soft and a little more dot gain. A hard-sized sheet leaves the ink on top: crisper, but slower to dry.
- Coating. Clay-coated, gloss, silk, aqueous- or UV-varnished and laminated surfaces do not absorb. Inks that dry partly by soaking in struggle there.
- Colour and brightness. Most screen inks are semi-transparent, so the paper shows through. A bright white sheet gives the cleanest colours; a cream or grey sheet shifts every one of them.
- Grain and dimensional stability. Paper swells and shrinks with humidity, and about four times as much across the grain as along it. This is the main enemy of multi-colour registration (see below).
- Permanence. For an edition you sell, look for acid-free (pH neutral), ideally cotton or at least lignin-free paper, and ask the ink maker for lightfast pigments.
The paper families, and what each is good for
Smooth uncoated cover (the workhorse)
Uncoated cover stock from 200 to 300 g/m² is what most poster printers start with. It takes water-based ink without fuss, is flat enough for halftones, and costs a fraction of art paper. Screen printers name lines such as French Paper and Domtar Cougar; in Europe, look for the uncoated ranges of your paper merchant and ask for a smooth finish. Good for: flats, posters, halftones up to about 55 LPI. Weak spot: large dark solids look heavier and less precise than on coated paper, so allow a little less saturation in the artwork.
Cotton rag and printmaking paper
BFK Rives, Arches, Somerset, Stonehenge and Crane’s Lettra are the names printers use for editions. The cotton fibre is permanent, tough and lovely to handle, and it takes ink with a soft, deep matte. The catch: with water-based ink a rag sheet soaks up the body of the ink and can flatten colours, and, like all paper, it swells and shrinks with the humidity and the water in the ink. Good for: limited editions, flat colours, soft overprints. Weak spot: fine halftones on textured surfaces. If the rag sheet is textured, lower the LPI and let the dots be larger.
Coated and gloss stock
Coated sheets give the sharpest, most photographic result and the least ink soaking in, but they are the hardest to get right. Water-based ink dries partly by absorption and partly by evaporation, so on a coating it sits wet and can fail to bond. Solvent-based and UV-curable inks are the usual answer. Whatever you choose, run an adhesion test before the edition (see below). Good for: photographic work with a UV or solvent system. Weak spot: hobby water-based inks.
Coloured and dark stock
Coloured papers such as the Colorplan range are used for both letterpress and screen printing. On dark stock a semi-transparent ink loses to the paper: a blue on black paper turns dull or disappears. The fix is an opaque white layer under the colour. Printers report that white often needs two passes, and that white ink is thick, so a coarser mesh (110–156) helps. PrintFilmReady does not add an underbase in paper mode (that is a garment feature), so make the white layer from the artwork silhouette in your design software. Order paper swatches of the exact shade first and test the white on it.
Kraft, recycled and board
Rough, absorbent and characterful. Excellent for bold flat colours, stationery and packaging; poor for fine halftones. Test everything: batches differ more than with art paper.
Match the screen to the paper
Two things change when the paper changes. How much ink you want on the sheet, and how fine a dot the sheet can hold.
Ink film. A coarser mesh and a thicker stencil lay down more ink. An absorbent sheet can take a generous film because a good part sinks in; a hard-sized or coated sheet cannot, so a thick film on it spreads, dries slowly and curls the paper. Rule of thumb: absorbent paper, coarser mesh for solids; non-absorbent paper, finer mesh and a thinner deposit.
Dot size. On paper the dot gain is small (about 3–10% in our reference data, against 15–35% on textile), so a given mesh can carry a finer line screen. These are the paper presets in PrintFilmReady:
| Mesh | Line screen | Smallest dot | Usable tonal range | Good for |
|---|---|---|---|---|
| 156 | 35 LPI | 0.26 mm | 10–90% | Bold halftones, posters, textured stock |
| 230 | 55 LPI | 0.14 mm | 7–93% | The all-round paper screen for halftones |
| 305 | 70 LPI | 0.09 mm | 5–95% | Fine detail, smooth stock, process colour |
| 355 | 80 LPI | 0.08 mm | 5–95% | The finest work, on the smoothest sheets |
Keep the mesh at roughly 4 to 4½ times the LPI so the halftone does not fight the weave (see moiré is a ratio problem). On a textured sheet, drop one step: use 35 LPI where the chart says 55, and accept larger, rounder dots. A rough surface cannot hold what a smooth one can, whatever the mesh.
For the mesh itself, supplier guides give a consistent picture: about 110 for bold solids and white layers, 156 to 200 for general poster work and text, 230 for halftones and fine text, 280 to 305 for very fine detail and process colour. For metallic and fluorescent inks the sources disagree (anything from 30 to 110 for heavy metallics), so follow the ink maker’s data sheet and test.
Ink on paper
| Ink system | How it dries | Best on | Watch out for |
|---|---|---|---|
| Water-based (including water-based acrylic) | Evaporation and absorption | Uncoated paper, rag, kraft | Soaks into rag; the water swells the sheet; dries in the screen if you pause |
| Solvent-based | Evaporation | Coated and non-absorbent stock | Fumes (VOC), ventilation, fast screen drying |
| UV-curable | Instant, under UV light | Almost anything, including coated | Costly equipment; thick deposit that can curl paper; good rub resistance |
| Plastisol | Heat | Textiles | Not an ink for paper |
Humidity, grain and registration
Registration on paper is lost to water, not to the press. A patent on proofing gives typical figures for ordinary paper: going from 50% to 80% relative humidity the sheet grows about 0.25% across the grain but only about 0.06% along it. In the other direction, 50% to 20% shrinks it about 0.1% across and 0.06% along. Individual papers differ, but the ratio of roughly four to one is the point.
Do the sum for a 50 cm sheet in a damp week. 0.25% of 500 mm is 1.25 mm. At 55 LPI one halftone cell is 25.4 ÷ 55 = 0.46 mm, so the sheet has moved by almost three cells between two colours. No registration mark can save that. What helps:
- Acclimatise the paper. Take it out of the wrapping and let it rest in the print room for a day or two, with the pile separated, so the middle of the stack is not still at the warehouse humidity.
- Keep the room steady. Printers and paper handlers aim for a constant humidity, commonly quoted around 50–55%. Steady matters more than the exact figure.
- Print all colours in one session. Print each colour soon after the previous one has dried, not days later. Every water-based layer also adds moisture to the sheet.
- Know the grain. Check the packaging: the grain direction is given with the size (a 25×38 skid has its grain along the 38 inch side). Or bend the sheet gently: it resists more across the grain than along it. Cut so that the direction that moves most is the one your registration can tolerate.
- Do not stretch it. Heavy squeegee pressure stretches light paper.
- Proof 10 to 20 sheets and see how much register drifts before you commit to the run.
Weight, curl and a sheet that sticks to the screen
- Use the least off-contact that still snaps the screen free. Suppliers quote about 1.5 mm to start and no more than about 3 mm; a bigger gap throws registration. Too little gap and the screen peels slowly and the sheet follows it.
- Tacky ink pulls light paper off the platen. A lower-tack ink, or a little reducer, helps; so does a tacky platen or a vacuum table.
- Thick deposits curl paper. That is typical with UV and with big solids. Dry flat and use a heavier sheet for heavy coverage.
- Dry flat, not stacked wet. Racks beat piles. Water-based ink on thin stock cockles if it dries unevenly.
A one-evening paper test
An hour of testing beats any chart, including this one. For each paper you are considering:
- Cut test strips from the same sheet, in the same grain direction.
- Print a test film with a step wedge, a 50% tint, fine lines, a solid and a registration cross, through the screen you intend to use.
- Look at the 5% and 95% steps with a loupe. Dots that merge or vanish tell you the line screen is too fine for this paper.
- Let it dry, then press tape on the solid and peel it. Any ink on the tape means poor adhesion.
- Check the next day for curl, colour shift and rub.
- Write the paper, mesh, ink and result on the back of the strip. In a year you will want to know.
How sure are we
The numbers for mesh, line screen, smallest dot and tonal range are the paper presets built into PrintFilmReady. The rest of the practical advice comes from supplier guides and printers’ own experience (mesh guide, off-contact, inks, poster paper, a screen printers’ thread) and from a patent that lists typical paper movement, not from a standards body. Where those sources disagree, as with metallic ink, we said so. Treat every figure as a starting point.
Common questions
What weight of paper is best for screen printing posters?
A smooth uncoated sheet of about 200–300 g/m² (roughly 80 to 110 lb cover) is the usual starting point. It is stiff enough to stay flat on the press and take wet ink. Lighter paper tends to cockle and stick to the screen.
Can I screen print on gloss or coated paper?
Yes, but not with an ink that depends on soaking in. Water-based ink may not bond to a coating; solvent-based and UV-curable inks are the usual solutions. Run a tape test on a printed strip before you commit to an edition.
Why do my colours look flat on cotton paper?
Cotton rag is absorbent. With water-based ink it soaks up part of the ink body, which flattens the colour. Use a coarser mesh or thicker stencil for a heavier film, or a less absorbent sheet, and print all layers in one session.
Which mesh should I use for halftones on paper?
Start at 230 mesh with 55 LPI on a smooth sheet, and go to 305 only when the paper is smooth enough to hold dots of about 0.09 mm. On a textured sheet use a coarser line screen. Keep the mesh at roughly 4 to 4½ times the LPI.
Can I print on black or dark paper?
Yes, with an opaque white layer under the colours, usually two passes of white, and a coarser mesh for the white. Test on the exact shade first, because semi-transparent inks disappear on dark stock.
Why does my second colour not register on a damp day?
Paper swells with humidity, about four times more across the grain than along it. Acclimatise the stock, keep the room steady and print all colours in one session.
Set the paper once
Choose Paper in PrintFilmReady and the mesh presets switch to the finer line screens and wider tonal range that paper can hold. Free trial, no account.
Built by a screen printer, for screen printers. What you tell us decides what gets built next. Write a review · Send an idea