
A pencil sketch is full of things a block cannot print: grey, soft edges, hairlines, shading that fades out. A linocut or woodcut has two states only, ink and no ink. So the work between sketch and block is a translation, and most of it is a series of decisions you make before you cut. Photo to woodcut covers photographs; this is the same job for a drawing.
1. Get the sketch into the computer
- Draw dark on white. A soft pencil scans pale and grey. Go over the lines you want with a black pen or marker.
- Scan flat, or photograph in even light. Shadows from a phone camera turn into grey patches that are hard to remove later.
- Save as PNG, about 300 PPI at the size of the block. A 10 cm block wants roughly 1200 pixels across (see file resolution).
2. Decide what prints
Every area is either printed or carved away. There are two ways to draw a line:
- The raised line. You clear the material on both sides of the line, and the line itself takes the ink: black on white paper.
- The carved line. You cut the line away, and it prints as a white line in a black area.
A printmaker’s guide favours the first for most work and warns that an outline cut too thin makes a weak, uninteresting print. Mark the negative space on a copy with a marker so you can see what gets carved away.
3. Make it bold and flat
- Thicken the lines. Hairlines disappear in the carving. Redraw them with a thicker pen, or thicken them in an image editor, until the narrowest line is wider than the narrowest cut you can make.
- Turn shading into shapes. Hatching and soft shadows become a solid black area, a pattern of cut lines, or nothing. Pick one for each area.
- Remove the grey. Set a threshold so that everything is pure black or pure white. Anything in between will give edges you did not draw.
- Check the narrow gaps. Two lines that almost touch merge into one black shape, and the white gap between them is too narrow to cut.
4. Let an AI image tool do the cleaning (optional)
If you do not want to redraw by hand, you can give your sketch to an image generator that accepts a reference image and ask it for a clean version. The principle is the same as in AI prompts for screen printing: ask for flat shapes, not soft shading. Starting points:
| Goal | Add to your prompt | Avoid |
|---|---|---|
| Clean up the sketch | “Redraw this sketch as a linocut: same composition, bold black ink lines of even thickness, solid black areas, pure white background, no grey, no shading” | “realistic”, “detailed”, “soft shadows”, “pencil” |
| Carved white lines | “Black linocut print, the design is carved as white lines in solid black, thick white lines, bold negative space” | “fine white hatching”, “gradient” |
| Replace shading | “Shading as a few bold cut lines or solid shapes, no gradients, no crosshatching” | “smooth shading”, “fine texture” |
| Two or three blocks | “Three flat tones, light, mid and dark, each a separate flat shape with hard edges, no gradients” | “watercolour”, “airbrush” |
What goes wrong. The tool redraws instead of tracing. It may change proportions, drop a detail, add one you did not draw, or invent letters. It does not know that a thin line will break when you cut it. So:
- Put the result next to your sketch and check what moved or was added.
- Check the line widths and the gaps again (step 3). The AI image has no idea which line your gouge can cut.
- Many generators produce a small image: scale it up before you do anything else, then set the threshold again so the edges are pure black and white.
- Expect to touch up in an editor. Treat the result as a clean sketch, not a finished file.
5. Check it at the size of the block
- Print it at 100%, at the real size of the block.
- Squint test: black stays, white is carved away. Does the picture still read?
- Run a finger along the narrowest white gaps and the thinnest black lines. Can your smallest gouge make that cut, and will that line survive the roller?
6. Transfer it, and mind the mirror
A block prints as a mirror image, so the design has to be carved reversed, and writing most of all. There are two usual ways to get the drawing onto the block: carbon paper under the drawing, or a drawing on tracing paper placed face down on the block and rubbed. Which one flips the image is explained in lino and block printing layers: decide before you print or draw, and check the label in the margin of the guide.
Where PrintFilmReady fits
The tool does not draw or clean sketches: steps 1 to 4 happen in your editor or AI tool. Once you have a clean black-and-white or flat-colour file, load it in the Lino & Block tab. The halftone is off, each ink becomes one block, and every layer is printed solid black at the size you set, with registration marks and a margin that says which layer it is. For a multi-block print you get one guide per block. That guide is a carving pattern, not a film for a screen.
Sources
- Designing your lino print (Hickman Design): outlines cut too thin give a weak print, the raised line versus the carved white line.
- Transferring your image or design onto lino blocks (Hickman Design): carbon paper and the face-down rubbing transfer, and writing that has to be reversed.
No source we found gives a measured minimum line width for lino. The 0.8 mm in the tool is an assumption: set what your own gouges can cut. The prompts are starting points: every image generator reads them a little differently.
Common questions
How do I turn a pencil sketch into a linocut design?
Scan it, go over the lines you want in black, thicken the thin ones, turn everything into pure black and white, and check it at the size of the block. Then transfer it mirrored and carve.
Can an AI tool turn my sketch into a linocut design?
It can clean it up if you ask for flat black and white: bold lines, solid fills, no grey, no shading. It redraws instead of tracing, so compare the result with your sketch and check the line widths before you carve.
Which is better for a linocut: a raised line or a carved white line?
Both work. The raised line prints black on white and one printmaker favours it for most work. The carved line prints white in a black area and gives a bolder look. Decide before you draw the final version.
How thin can a line be?
It depends on your gouge and your lino. We found no measured minimum, so cut a test with your own tools and set that as your smallest cut. A line cut too thin gives a weak print.
Do I have to mirror the drawing?
The print is the mirror of the block. Whether you flip the drawing yourself depends on how you transfer it. Writing is the part that goes wrong most often, so test with a word before you carve.
Make your carving guide
Load your clean drawing in the Lino & Block tab: one block per ink, solid layers, mirrored, with registration marks. Preview is free.
Built by a screen printer, for screen printers. What you tell us decides what gets built next. Write a review · Send an idea