
Pick your route
There are six sensible ways to get a design onto a block. They differ in what you do with the file, so choose the route before you set anything in the tool.
| Route | Block material | What you do with the file | Mirror | Good for / watch out |
|---|---|---|---|---|
| 1. Hand carve, lino | Linoleum, soft-cut rubber | Transfer the printout, then carve | Depends on the transfer | Bold shapes, learning, low cost. Lino wears and has no grain |
| 2. Hand carve, wood | Shina or birch plywood, cherry, pear | Transfer the printout, then carve | Depends on the transfer | Crisp lines, durable. Needs sharp tools |
| 3. Laser | PVC-free lino or rubber, Baltic birch, acrylic | Engrave the white areas from a 1-bit image | On | Fast, repeatable. Fumes, depth and char need care. Never PVC |
| 4. CNC router | Wood, some plastics | Trace to closed vector shapes, clear, then V-bit the edges | On | Large blocks, deep clearing. Needs a vector, not a bitmap |
| 5. Photopolymer plate | Polymer plate on a base | Print a negative film, expose, wash out in water | On (film wrong-reading, emulsion down) | Very fine detail and good for repeat runs. Needs a UV exposure unit and a relief press |
| 6. Photo-etched metal | Zinc or magnesium | Hand the file or film to a specialist engraver | Ask the engraver | Finest, most durable. Chemistry and equipment, so outsource |
Step 0: make the carving guide
All six routes start the same way. The full separation is in layers for lino and block printing, so here is only what the rest of this guide depends on.
- Open the tool, choose Lino & block and load your artwork. The halftone raster switches off and every layer becomes a solid shape.
- Set the number of inks to the number of blocks. One block: one ink. For a reduction print you still work from the same layers.
- Enter the width of your block, not of your paper, and print at 100%.
- For more than one block, tick kento registration marks: a corner mark and an edge mark in the same spot on every layer.
- Decide the mirror (next section), then download.
What is in the file. Black is where the ink goes, so black is the part that stays raised. White is what you cut away. Greys are decided at the halfway point: 50% or darker becomes black. The margin carries a label and registration marks, so crop to the artwork before you send it to a laser or router.
The mirror, once and for all
A block prints the mirror image of what is carved on it. So count how many times the image flips between the file and the paper.
| How the design reaches the block | Mirror artwork |
|---|---|
| Printout laid face down on the block (baking paper, glue, acetone or laser-print transfer) | Off |
| Printout face up, traced through carbon or graphite, pencil-rubbed or stuck on as a sticker | On |
| Laser or CNC working directly on the face of the block | On |
| Film laid emulsion down on a photopolymer plate | On |
Not sure? Put a word in the design. If it reads backwards on the block, you are right. The transfer methods are explained in transfer a print to wood: 7 methods.
Choose the block material
Lino and soft-cut rubber
Traditional linoleum is a layer of hardened oil on a jute backing. It carves cleanly, gives strong contrast and has no grain. Soft-cut rubber and vinyl blocks carve even more easily, so they suit beginners and classes. The price of softness is wear: lino loses sharp edges sooner than wood. Two warnings. Cut only as deep as an even floor needs, because going too deep exposes the backing fabric. And if the block is going near a laser, check that it contains no PVC (see the laser section).
Wood
- Shina plywood (a linden relative) is the usual recommendation: soft enough to carve easily and hard enough to hold a crisp line, and plywood warps far less than a solid plank. Hold a sheet up to a strong light before planning your image, since some sheets have voids. Cheaper “economy” shina may have a lauan core.
- Cherry is the traditional choice for the finest work. It is harder, so sharp tools are not optional. Pear is another classic. Maple is fine-grained but very hard.
- Birch plywood is cheaper and easy to find. Acceptable, though not as fine as the others. For lasers, Baltic birch is preferred.
- MDF is smooth and cheap in big sheets, but harder to cut than wood, its dust is a health hazard and some printmakers find it flakes when cleaned. It is also a poor choice for laser relief (see below).
- End grain hardwood is for wood engraving with gravers, not for gouge work. It allows much finer marks.
Whatever you pick, sand the face smooth, store boards flat and dry, and test-print early.
Hand tools and a bench that behaves
- U-gouges hollow out areas; a wide one clears background quickly without leaving ridges. V-gouges cut lines and edges. A craft knife cuts the outline of fine shapes.
- Sharpness is safety. A blunt gouge slips. A sharpening routine from a general tool guide: soak a whetstone for 5 to 10 minutes, hold a U-gouge at about 15° against the part of the stone that matches its curve, and lay a V-gouge flat on each side in turn.
- Hold the block still. Masking tape, adhesive putty or a non-slip mat. Always carve away from your body and keep the holding hand behind the cutting edge.
- In a cold room lino gets brittle. Warm it briefly with a hairdryer or near a heat source, without overheating it.
- Test every tool on a scrap of the same material before it touches the block.
Carving: the order of work and the tricks that save a block
- Mark what goes. Hatch the white (cut-away) areas with a marker on the transferred design, so you never cut the wrong side.
- Cut the outlines first with a V-gouge or knife, then clear the inside with a U-gouge. Outlines first stops you pushing a clearing cut across a line you need.
- Cut shallow, in stages. You do not need deep cuts. An even floor matters more than depth. Start light and deepen only where large blank areas print speckle.
- Mind the ridges. Leftover ridges in cleared areas pick up ink and print as speckle. Carve in one direction when clearing, or keep the texture on purpose.
- Keep a sloped shoulder. Cut thin raised lines with a slight slope to the sides, like a tiny roof, so they do not snap off. Never undercut a thin line.
- Leave a border. A margin of uncut block around the design is handy for registration and keeps paper from catching on the edge.
- Proof early and often. Print, look, carve more. If the block needs more cutting, clean off the ink with warm water, let it dry and re-carve before re-inking.
- Do the registration cuts last on multi-block jobs, and cut them identically on every block (see the kento section).
The laser
A laser turns the file into relief with no hand work: it removes the white areas, leaving the black raised. Lasers vary enormously, so everything below is a method and a starting point, never a fixed recipe. Run a test grid on scrap first.
Safety first: never put PVC or vinyl in a laser
Chlorine compounds from PVC and other vinyl plastics permanently damage a laser and release fumes that are harmful to breathe. Laser-safety guidance says never to engrave PVC, vinyl or an unknown material. If you are not sure what a block is made of, get the supplier’s safety data sheet or do not laser it. Never run a laser unattended, and always extract the fumes to the outside.
Prepare the file for a laser
- Mirror on. The laser works on the face of the block (see the mirror table).
- Crop to the artwork. Remove the label margin, or keep the crop edges as your frame.
- Engrave the white. The laser removes material where it burns. In your laser software, either invert the image or set it to engrave white. If you forget, you carve the design and leave the background raised.
- Use the file as a 1-bit image. The guide is pure black and white, so use threshold mode, not a grey dithering. An image resolution in the region of 250 to 333 dpi is commonly used for relief engraving; the film resolution in the tool (360 dpi by default) is in the same range.
Materials and depth
- Lino and rubber. Only PVC-free, laser-safe stock. A university printmaking lab reports working at 250 dpi in two passes on a rubber preset, and notes that the jute backing needs extra passes to cut through. Too much heat makes lino leach oil, so they raised speed to keep it cool. Treat these as an example from one machine.
- Baltic birch plywood. Preferred for its even layers and low resin. A university woodcut project engraved quarter-inch Baltic birch in two passes at 333 dpi. A laser manufacturer suggests 3 to 4 slow, high-power passes for depth, then one or two fast, low-power passes to remove smoke residue. Cheap plywood with a plastic-resin core can melt instead of burn.
- MDF. The glue releases formaldehyde when lasered, and one guide calls it a poor choice for relief because of depth limits and charring. Avoid it.
- Do not pause a job. A block paused and restarted early on showed a faint line in the print.
- Clean the block. Char is a brown residue. Scrub gently with a toothbrush, a little water and soap, then dry thoroughly with compressed air. Sanding lightly also works. Consider sealing wood if you will use water-based ink for a long edition.
- Deep blank areas. Paper can sag into engraved cavities. The university project added a step at the leading and trailing edge of the block and runners at the side of the press bed so paper would not be pulled in.
Acrylic (plexi)
Acrylic sheet can be laser-engraved as a relief plate: the raised, uncut areas take the ink. It is smooth, so it prints sharp and cleans easily. Practical points from makers who use it:
- Mirror the whole design, or the print comes out backwards.
- The engraving need not be deep. Clean, even edges matter more than depth. 3 mm acrylic is strong enough that engraving the reverse side does not show through, so a failed plate can be washed and re-engraved on the other face.
- Add registration marks and cut the plate larger than the paper.
- Ink matters. Use an ink that dries properly and cleans up with water. Makers report that some inks lack a drying agent and rub off later, that some thread when the paper is lifted, and that an over-damp sheet makes water-based ink bleed. Test your ink and paper combination.
- Do not confuse relief with drypoint. Scratching a line into acrylic by hand and wiping ink into it is intaglio, the opposite principle: the cut lines print. Everything in this guide is relief, where the raised parts print.
CNC router and hobby cutters
- A CNC needs vectors. The file from the tool is a bitmap. Trace it in Inkscape or Illustrator with a black-and-white trace, and check the result: you want closed, filled shapes for the raised areas, not stroked outlines or open paths.
- Mirror first, before you generate the toolpath.
- Clear, then refine. A V-bit alone is too slow for large background areas and leaves an uneven floor. Use a larger flat or ball-nose bit to clear the waste, then a fine V-bit for the edges. A bigger bit removes material faster, a smaller one holds detail.
- Test on scrap for depth and bit choice. We found no tested lino-specific CNC settings.
- Hobby cutters. A vinyl cutter can follow the same traced shape to cut thin stencil material. We found no reliable tested method for using one to make a printing plate, so treat that as an experiment.
Photopolymer and metal
Photopolymer plates from your film
This is the route that uses the film itself. A photopolymer plate hardens where UV light reaches it, and the unhardened rest washes out in water, leaving a fine relief that prints on a letterpress or relief press. Steps:
- Make a negative. The film must be transparent where the plate should print and dense black elsewhere. That is the opposite of the carving guide, so invert the image. The tool has no invert button, so do it in any image editor.
- Print it dense. Use the settings in printer settings for films. If the black is not opaque enough, stack two films to block more UV.
- Mirror on, emulsion down. The plate is exposed with the film printed side down, so the film has to be wrong-reading. That is what the mirror option produces. The printed plate then prints right-reading. If you order negatives from a bureau, ask for the orientation they call right-reading, emulsion up, because it flips when laid down.
- Expose with contact. Hold the film flat against the plate with glass or a vacuum frame. Find the exposure time with the manufacturer’s data sheet and a step gauge, since fine detail and solids want slightly different times.
- Wash out with a soft brush in water; hard brushes scratch fine detail. Overlong washing degrades the plate and over-exposure fills in the finest lines.
- Dry and post-expose with a final UV exposure, then mount on a base. Keep notes on film density, contact, exposure and washout; when something goes wrong, you will know which variable changed.
Photo-etched zinc and magnesium
Zinc and magnesium are the standard metals for relief blocks (letterpress “cuts”). Metal holds more detail than wood or lino and lasts far longer. The etching is a chemical process, so most people commission it from a specialist engraver. Copper is normally used for the opposite principle, intaglio, where the etched lines hold the ink. If you want to etch yourself, work from a technical printmaking manual: etching chemistry is beyond this guide.
Inking and printing
- Roll out a small, even film. Roll a square of ink the size of the roller. Good coverage sounds like a faint, sticky hiss, not a squelch. Too much ink or pressure rounds the edges and fills the detail.
- Water-based ink cleans up without solvents but dries quickly on the roller, plate and block, so work briskly or add retarder. Oil-based ink stays open longer.
- Keep the background clean. Roll lightly and avoid dragging the roller into cut areas.
- Print. Lay the paper on the inked block, face down, without letting it slide. Burnish the whole area with a baren, a spoon or your hand, or use a press. Plain 80 g/m² copy paper is fine for proofs.
- Choose the paper for the job in our paper guide; the surface, weight and absorbency decide how a solid reads.
Several blocks: registration
Registration is covered in align the marks, not your eyes and the layers guide. Three points that matter for blocks:
- Kento. The corner mark and edge mark from the tool tell you where to cut the kento notches on every block, in the same place each time. Cut them at the same stage of every block, ideally before carving the design.
- Print light to dark, because opaque dark ink covers light ink and the reverse fails.
- Overlap on purpose. A shape that runs slightly under its neighbour hides a white gap. Pro has an Overlap setting that does this for you (0.1 to 1 mm, per ink if you like); without Pro, build the overlap into the artwork.
When it goes wrong
| What you see | Likely cause | Fix |
|---|---|---|
| The whole print is backwards | Mirror counted wrong | Re-do the transfer or file with the other mirror setting; test with a word |
| Laser engraved the design, background still raised | Engraved black instead of white | Invert the image or engrave white |
| Speckle in blank areas | Ridges or too shallow a floor | Clear again in one direction, or deepen slightly |
| Fuzzy, rounded edges | Too much ink or pressure; blunt tool | Thinner ink film; sharpen; lighter burnishing |
| Thin lines break off | No sloped shoulder; soft material | Recut with sloped sides; use harder stock or wood |
| Paper picks up ink in deep cavities | Paper sags into engraved areas | Raise the surround, add runners, or use a frisket |
| Faint line across a laser block | The job was paused | Re-engrave without stopping |
| Polymer plate loses fine detail | Over-exposure or long washout | Shorter exposure; check with a step gauge; brush gently |
| Polymer plate background does not wash out | Film not dense enough, or positive used instead of negative | Invert; double the film; raise density |
How sure are we
The tool facts (solid black on white, mirror, kento marks, 50% threshold, exact block size) are checked against the app. Everything about tools, wood, lasers, acrylic, CNC and photopolymer comes from printmaking courses, laser-safety guidance and makers’ own reports, not from a standards body. Where sources only describe one machine, we said so. Sources: a university lino laser lab, a woodcut laser project, laser unsafe materials, a university laser safety guide, wood for printmaking, shina plywood, a linocut guide, sharpening gouges, relief engraving in acrylic, a maker’s laser-cut plate write-up, tracing bitmaps, CNC relief cutting, a photopolymer handout and a platemaker guide. Test every setting yourself before you trust it with a good block.
Common questions
Can I laser-cut or engrave lino?
Only if the lino is PVC-free and laser-safe. PVC and vinyl release chlorine compounds that damage the laser and harm you, so never use a block you cannot identify. Get the supplier’s safety data sheet, extract the fumes outside and never leave the machine unattended.
Which wood is best for a woodcut?
Shina plywood is the usual starting point: easy to carve, holds a crisp line and warps little. Cherry is the traditional choice for the finest detail but needs sharp tools. Birch plywood is a cheaper alternative, and Baltic birch is the one to use in a laser.
Do I mirror the file for a laser?
Yes. A laser works directly on the face of the block, and a block prints as the mirror of what is on it, so the file must be mirrored. Also tell the laser to engrave the white areas, so the black stays raised.
Can I use my PrintFilmReady film for a photopolymer plate?
Yes, with two changes. The plate needs a negative, so invert the image so that the part that should print is clear. Mirror it so the film is wrong-reading when laid emulsion down. Print it dense, and stack two films if one does not block enough UV.
Do I need a press?
No. Hand burnishing with a baren, a spoon or your hand works for lino and wood. A press gives even pressure over large areas and is needed for photopolymer and metal plates.
What file do a laser and a CNC need?
A laser takes the 1-bit image (threshold mode), mirrored, with the white areas engraved. A CNC needs vector shapes, so trace the image with a black-and-white trace, check that the shapes are closed and filled, and mirror before making the toolpath.
Make the carving guides
Choose Lino & block, set the width of your block, tick kento marks, and get solid, mirrored guides, one per colour. Free trial.
Built by a screen printer, for screen printers. What you tell us decides what gets built next. Write a review · Send an idea